{"product_id":"silox-epw-857-in-ral-7030-farbig-pigmentierte-epoxydbeschichtung-35-68-kg","title":"Silox EPW 857 in RAL 7030 - colored epoxy coating (35.68 kg)","description":"\u003cp\u003e\u003cstrong\u003eColored pigmented epoxy coating for damp substrates\u003c\/strong\u003e EPW-857 is a water-emulsified, colored pigmented 2-component system based on a special epoxy resin and hardener compound. The product is recommended as an abrasion-resistant and highly chemical-resistant decorative protective coating for all mineral surfaces and also for mastic asphalt. Like all SILOX EPW grades, EPW-857 can be diluted with water. The coating is characterized by excellent adhesion - even on damp substrates. Cured coatings made of SILOX-857 are not vapor-tight; therefore, the drying out of treated concrete surfaces or water vapor diffusion from the substrate is not significantly obstructed, and adhesion failure, blistering, or similar damage due to water exposure at the coating-substrate interface cannot occur. Colored protective coatings for concrete surfaces in industry, in sewage treatment plants, as well as for garage and basement floors and similar areas of application. Durable protective coatings for walls that must be frequently decontaminated or cleaned with high-pressure water or steam jets, e.g., in tunnels, in food industry facilities, etc. EPW-857 consists of two components that must be thoroughly mixed in a mixing ratio of 2:1 before application. The mixture can then be diluted with clean water as needed to adjust the brushing or spraying viscosity.\u003c\/p\u003e\n\u003cp\u003eWhen using spraying equipment, ensure that aerosols (spray mist) generated—especially when spraying with high-pressure (airless) devices—do not contaminate adjacent components. The quality of the dried coating films is so high that such contamination can hardly be removed. Due to the cross-linking reaction of the epoxy binder that begins immediately after mixing the components, the pot life of the mixtures from the EPW 857 components is naturally limited. Higher temperatures additionally accelerate the setting reaction. Since the end of the pot life in water-emulsified epoxy systems of this type is \u003cu\u003enot\u003c\/u\u003e recognizable by the typical increase in the viscosity of the mixture, this property must be carefully observed. To avoid errors, it is recommended to mix only as much material as can be easily processed in a manageable time. Substrates must be clean and free of dust and other contaminants that act as release agents. They must have sufficient load-bearing capacity or be pretreated with a non-pigmented primer with sufficient penetration depth. Observe the relevant technical rules for painting and coating work (e.g., DIN 18363).\u003c\/p\u003e\n\u003cp\u003eConsumption is naturally dependent on the roughness depth and absorbency of the concrete. For machine-smoothed concrete floors and smooth-shuttered concrete surfaces, consumption values of approx. 150 - 300 g\/m\u003csup\u003e2\u003c\/sup\u003e per coat—depending on the application—are to be expected. Machines and tools can be cleaned with water with the addition of a commercial wetting agent (dish soap). It is advisable to use hot water for this purpose. To reliably prevent valves and feed pistons in spraying machines from sticking, we recommend flushing the equipment with our safety solvent HydroSolv-520 after rinsing with water and then filling it with HydroMoll 522 care agent for storage preservation. Contamination from cured material is difficult to remove; we therefore recommend protecting adjacent components by masking and covering them, and always removing unavoidable impurities immediately.\u003c\/p\u003e\n\u003ch2\u003eSystem accessories for Silox EPW 857 in RAL 7030 - colored pigmented epoxy coating\u003c\/h2\u003e\n\u003cp\u003eSilox EPW 856 – transparent epoxy impregnating sealer; Silox Sealing Slurry 863 – universal sealing and coating compound\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eContents:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003e5.96 kg container: follows shortly\u003c\/li\u003e\n\n\u003cli\u003e35.68 kg container: A component 29.94 kg, B component 5.74 kg\u003cstrong\u003e\u003cbr\u003e\u003c\/strong\u003e\n\n\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"ARCAN","offers":[{"title":"5.96 kg","offer_id":62887813382474,"sku":"1056","price":109.21,"currency_code":"EUR","in_stock":true},{"title":"35.68 kg","offer_id":62887813415242,"sku":"1055","price":549.85,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Beschichtungen-_C2_BB-Garagensiegel-_C2_BB-Silox-EPW-857-in-RAL-7032-e1445430295538.jpg?v=1782831215","url":"https:\/\/shop.arcan.biz\/en\/products\/silox-epw-857-in-ral-7030-farbig-pigmentierte-epoxydbeschichtung-35-68-kg","provider":"ARCAN GmbH Abdichtungen – Handwerkerstore","version":"1.0","type":"link"}