{"product_id":"blocsil-910-stabilisierung-von-fugen-und-verguetung-von-oberflaechen-10-kg","title":"BlocSil 910 - Joint stabilization and surface refinement (10 kg)","description":"\u003cp\u003eBLOCSIL 910 is designed for stabilizing joints and enhancing the surfaces of cast stone and concrete pavers. BlocSil 910 is a reactive polymer that has been dissolved in water and is very easy to use. It solidifies and stabilizes joint fillings, preventing weed growth as well as hollowing out by ants. The surface is impregnated and protected against dirt and abrasion. BLOCSIL stabilizes the joint filling. The sand in the joints is bonded and solidified like mortar. It can no longer be washed out or lost through sweeping, even when using heavy road sweepers in pedestrian zones! Ugly growth of grass and weeds is permanently prevented, and the plague of ants also comes to an end with BLOCSIL.\u003c\/p\u003e\n\u003ch4\u003eImportant: BLOCSIL 910 does not seal the joints! They therefore remain permeable to water and air. Roots can continue to breathe and water can seep through!\u003c\/h4\u003e\n\u003cp\u003eTreatment with BLOCSIL gives concrete slabs and pavers a good and well-maintained appearance in the long term. The natural effect of the joint fillings and pavement surfaces is not altered by treatment with BLOCSIL 910. However, BLOCSIL prevents stains, adhesions, and tire marks. The clean surface visually enhances the areas and associated objects and saves costs on time-consuming cleaning work. Not only in private areas, but also increasingly in public traffic areas, pedestrian zones, at public buildings, and much more... BLOCSIL 910 impregnates, solidifies, and hardens the concrete surface. Wear caused by abrasion (and thus dusting and sand erosion) is prevented. Oil, grease, fuel residues, and other dirt—even chewing gum residues—are much easier to remove from a surface treated with BLOCSIL.\u003c\/p\u003e\n\u003ch4\u003eApplication\u003c\/h4\u003e\n\u003cp\u003eBefore treatment with BLOCSIL, the paved areas must be dry, clean, and free of dust. The sand used for the joint filling should comply with relevant standards and guidelines (correct grain distribution!). Any dirt and growth must be removed. No special expertise is required for the application of BLOCSIL 910. The product is applied generously and evenly to the clean paved area, most easily by pouring with a watering can equipped with a fine rose head. After pouring, excess material must be immediately and thoroughly scraped off the surface of the slabs and stones using a rubber squeegee (preferably with a foam rubber blade). This technique ensures the necessary deep saturation of the joints and ensures that no excess material remains on the stone surfaces. BLOCSIL must not be applied during rain or at temperatures below +5°C. Freshly treated areas should be protected from rain for at least 12 hours. Protect adjacent components from contamination with BLOCSIL by covering or taping them off, or wash off the fresh product immediately with plenty of clean water. Once set, BLOCSIL is so resistant that it can hardly be removed from most surfaces without leaving residues. BLOCSIL is a reactive, water-emulsified synthetic resin with an integrated hardener. The product reacts upon contact with sand or concrete and, after the water has evaporated, quickly turns into a hard, practically completely insoluble, and absolutely colorless plastic. Delivery form: Ready to use Property: Milky liquid with a faint odor Solids content: Approx. 25% Viscosity: 50 - 75 mPa.sec Labeling: None; Not classified as hazardous according to Regulation (EC) No. 1272\/2008 Drying times: 1 - 5 hours depending on substrate and weather* Setting time: Maximum 24 hours Consumption: Depending on substrate and joint condition, average value approx. 0.5 - 0.7 kg per m2\u003c\/p\u003e\n\u003ch2\u003eSystem accessories for BlocSil 910 - stabilization of joints and surface enhancement\u003c\/h2\u003e\n\u003cp\u003eStein Rein 915 – highly effective cleaning concentrate \u003cstrong\u003eContent: PE canister of 10 kg\u003c\/strong\u003e \u003cstrong\u003e\u003cspan style=\"color: #ff0000;\"\u003eAttention: Frost-sensitive material. Can only be shipped at temperatures \u0026gt; 5°C.\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":62357905178954,"sku":"1070","price":98.49,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Pflasterfugenm_C3_B6rtel-Steinreiniger-_C2_BB-BlocSil-910-10-kg-e1444140831889.jpg?v=1782831233","url":"https:\/\/shop.arcan.biz\/en\/products\/blocsil-910-stabilisierung-von-fugen-und-verguetung-von-oberflaechen-10-kg","provider":"ARCAN GmbH Abdichtungen – Handwerkerstore","version":"1.0","type":"link"}