{"title":"Liquid membrane","description":"\u003ch1\u003e\u003cspan\u003e– Seamless waterproofing for wet rooms\u003c\/span\u003e\u003c\/h1\u003e\n\u003cp\u003e\u003cspan\u003eLiquid membranes are ready-to-use, flexible sealing coatings for interior areas. They are applied before laying tiles and slabs and, once dry, form a seamless, water-impermeable protective layer that reliably protects the substrate from moisture.\u003c\/span\u003e\u003c\/p\u003e","products":[{"product_id":"duroflex-m-900-fluessigfolie-zur-abdichtung-von-beton-und-estrich","title":"DuroFlex M 900 - Liquid membrane for sealing concrete and screed","description":"\u003cp\u003e\u003cb\u003e\u003cb\u003eLiquid foil for waterproofing concrete \u003c\/b\u003e\u003c\/b\u003e DuroFlex - 900M is a highly efficient protective coating for concrete against the aggressive components of silage. The product consists of only one component and is easy and trouble-free to apply.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eSilage containers\u003c\/li\u003e\n\n\u003cli\u003eWet rooms (bathrooms)\u003c\/li\u003e\n\n\u003cli\u003eBalconies (under the final surface)\u003c\/li\u003e\n\n\u003cli\u003eTerraces (under the final surface)\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eSilage – green fodder prepared by fermentation – is produced by the fermentation of plants in the absence of air. Fermentation is a form of lactic acid fermentation. Unavoidable by-products of this process are acidic, aqueous leachates that contain lactic acid, but also butyric acid and acetic acid. These organic acids are extremely aggressive; they attack concrete surfaces and destroy them upon prolonged contact. The leachate escaping from silage silos also contaminates the groundwater. By coating with DuroFlex-900M, which was specially developed for this application, concrete components are safely protected and sealed against silage runoff. DuroFlex-900M is an emulsion of a self-crosslinking, rubber-like polymer, acid-resistant silicate fillers, color pigments, additives, and water. After application, the product dries very quickly into a homogeneous, liquid-tight foil (membrane) with very good resistance to alkalis, acids, and weather influences. Sealing foils made of DuroFlex-900M are seamless and jointless, highly elastic, and bridge cracks in the substrate.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eResistant to silage components\u003c\/li\u003e\n\n\u003cli\u003eFlexible and highly elastic\u003c\/li\u003e\n\n\u003cli\u003eCan also be applied to damp substrates\u003c\/li\u003e\n\n\u003cli\u003eHigh abrasion resistance\u003c\/li\u003e\n\n\u003cli\u003eContains no solvents\u003c\/li\u003e\n\n\u003cli\u003eBridges cracks and is dirt-repellent\u003c\/li\u003e\n\n\u003cli\u003eExcellent adhesion to concrete\u003c\/li\u003e\n\n\u003cli\u003eFast drying\u003c\/li\u003e\n\n\u003cli\u003eAlkali-resistant, also suitable for new concrete and fresh plaster\u003c\/li\u003e\n\n\u003cli\u003eEasy and trouble-free to apply\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eDuroFlex-900M is ready to use, with a thick, slightly thixotropic consistency. It can be applied like conventional dispersion paints, but it is better and more efficient to apply it by spraying. For reliable protection of concrete surfaces, DuroFlex membranes should be at least 600 µm \/ 0.6 mm thick (dry), corresponding to a wet coating thickness of 1 mm and a consumption of 1200 grams per m2. The coating should always be applied in two layers and in a cross-pattern to avoid defects. Different coloring of the two layers allows easy control over the even application of the coating; we therefore recommend always working in \"two colors\". The substrate must be load-bearing, clean, and free of all substances that could act as release agents. For concrete, voids, air pores in the surface, cracks over 0.1 mm wide, breakages, etc., must be repaired. UP Stone Filler 1013 is particularly suitable for this work. Masonry surfaces must be clean and fully jointed, or (for safety) either plastered smooth* or coated with an elastic sealing slurry*. * Cement plaster of mortar group III, expediently treated with SILEX-956 * SILEX-947 (highly elastic organomineral sealing slurry) It is recommended to prime new, smooth-formed concrete or plaster surfaces with an adhesive primer. For silage containers and similar demanding applications, we recommend Silox EPW-856; for simpler applications, DuroFlex 900-P Primer is suitable. Always prime highly absorbent substrates to prevent the coating from \"burning\" (drying too fast). If necessary, DuroFlex-900 M can be diluted with water (up to 10%, e.g., to adjust the spray viscosity). To improve abrasion resistance and for a non-slip surface, sharp-washed quartz sand – grain size e.g., 0.3 - 0.6 mm – can be mixed into the first DuroFlex coating or the freshly applied coating can be dusted with it. DuroFlex-900M must not be used at temperatures below 7°C, or in rain or extremely high humidity. Intermediate coats must be completely dry before applying the top coat to prevent dry cracks in the coating surface due to tension. Working joints – e.g., at floor-wall connections, butt joints in precast concrete parts – can be additionally secured by embedding HydroFlex 275, a special joint tape, to absorb larger movements in the substrate. The joint tape is glued on before coating and then covered with the sealing foil. For substrates heavily prone to cracks, it is possible to easily embed commercially available reinforcing fleece made of glass or textile fibers into the DuroFlex membrane for reinforcement. Product in delivery form Binder Emulsion of butadiene rubber (SBR) Density Approx. 1.2 g\/ml at 20° Viscosity Thixotropic Odor Faint, specific to butadiene rubber pH Approx. 9.5 Color Light gray* Solvent content None Characteristic data of the sealing foil Water absorption 11% after 28 days Tensile strength 1 N\/mm² Elongation at break ≥ 600% Vapor diffusion equivalent 50 (m air layer thickness) Consumption * 1.2 kg \/ m² for 600 µm dry film thickness \u003c\/p\u003e\n\u003ch2\u003eSystem accessories for DuroFlex M 900 - Liquid foil for waterproofing concrete and screed\u003c\/h2\u003e\n\u003cp\u003eHydroFlex Sealing Tape 275 – Adhesive foil system for sealing joints and cracks Cembond M 947 flex – flexible sealing slurry for surface waterproofing Silipox 826 FlexBand Adhesive – Adhesive foil system for sealing \u003cstrong\u003eContents: 30 kg bucket\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan style=\"color: #ff0000;\"\u003eThe material is sensitive to frost and must not be transported or stored at temperatures below 5°C\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"13 kg","offer_id":62357904884042,"sku":"1057","price":154.12,"currency_code":"EUR","in_stock":true},{"title":"30 kg","offer_id":62357904916810,"sku":"1058","price":343.07,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Abdichtung-Beschichtungen-DuroFlex-M-900-_E2_80_93-Fl_C3_BCssigfolie-zur-Abdichtung-von-Beton-und-Estrich-klein.jpg?v=1782831219"},{"product_id":"silox-909-pool-mx-fluessigfolie-zur-abdichtung-von-schwimmbecken","title":"Silox 909 Pool MX - Liquid membrane for swimming pool waterproofing (30.3 kg)","description":"\u003cp\u003e\u003cb\u003eLiquid membrane for waterproofing concrete swimming pools\u003c\/b\u003e Silox 909 Pool Mx is an elastic liquid membrane for concrete, used for waterproofing against water. The product consists of 2 components that are mixed together. It is simple and easy to apply.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eConcrete swimming pools\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eConcrete components are waterproofed by applying a coating of Silox Pool 909 MX, which was specially developed for this application. Silox Pool 909 MX is an emulsion of a self-crosslinking, rubber-like polymer, acid-resistant silicate fillers, color pigments, additives, and water. After application, the product dries very quickly into a homogeneous, liquid-tight film (membrane) with very good resistance. Silox 909 MX waterproofing membranes are seamless and jointless, highly elastic, and bridge cracks in the substrate.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eFlexible and highly elastic\u003c\/li\u003e\n\n\u003cli\u003eCan also be applied to damp substrates\u003c\/li\u003e\n\n\u003cli\u003eHigh abrasion resistance\u003c\/li\u003e\n\n\u003cli\u003eSolvent-free\u003c\/li\u003e\n\n\u003cli\u003eBridges cracks\u003c\/li\u003e\n\n\u003cli\u003eExcellent adhesion to concrete\u003c\/li\u003e\n\n\u003cli\u003eFast drying (depends on weather conditions and layer thickness)\u003c\/li\u003e\n\n\u003cli\u003eAlkali-resistant, also suitable for new concrete and fresh plaster\u003c\/li\u003e\n\n\u003cli\u003eSimple and easy to apply\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eSilox 909 Pool is ready to use and has a thick, slightly thixotropic consistency. It can be applied like conventional emulsion paints by brushing, though spraying is better and more efficient. For secure protection of concrete surfaces, Silox membranes should be at least 600 µm \/ 0.6 mm thick (dry), corresponding to a wet coating thickness of 1 mm and a consumption of 1200 grams per m2. The coating should always be applied in two layers and in a cross-pattern to avoid voids. Using different colors for the two layers allows for easy monitoring of uniform application, which is why we recommend always working with \"two colors\". The substrate must be load-bearing, clean, and free of all separating substances. For concrete, surface cavities, air pores, cracks wider than 0.1 mm, breakouts, etc., must be repaired. UP Stone Filler 1013 is particularly well-suited for this work. Masonry surfaces must be clean and fully pointed, or (for greater security) they must be plastered smooth* or covered with an elastic sealing slurry*. * Cement plaster of mortar group III, appropriately treated with SILEX-956 * SILEX-947 (highly elastic organo-mineral sealing slurry) We recommend priming new, smooth-formed concrete or plaster surfaces with a bonding agent. For this, we recommend Silox EPW-856; for simpler applications, DuroFlex 900-P Primer is suitable. Always prime highly absorbent substrates to prevent the coating from burning. If necessary, Silox 909 can be diluted with water (up to 10%, e.g., to adjust spray viscosity). To improve abrasion resistance and provide a non-slip surface, either sharp-washed quartz sand (grain size e.g., 0.3 - 0.6 mm) can be mixed into the first DuroFlex coating, or the freshly applied coating can be blinded with it. Silox 909 must not be applied at temperatures below 7°C, in rain, or in extremely high humidity. Intermediate layers must be completely dry before applying the topcoat to ensure that no drying cracks form in the surface of the coating due to tension. The primer must also be completely dry before applying the subsequent coating. Construction joints – e.g., at floor-to-wall connections or joint gaps in precast concrete components – can be additionally secured by embedding HydroFlex 275, a special joint tape, to absorb larger movements in the substrate. The joint tape is adhered before coating and then covered with the waterproofing membrane. For substrates at high risk of cracking, it is possible to embed standard glass or textile fiber reinforcement fleeces into the membrane for reinforcement without difficulty. Product as supplied Binder Emulsion of butadiene rubber (SBR) Density Approx. 1.2 g\/ml at 20° Viscosity Thixotropic Odor Faint, specific to butadiene rubber pH Approx. 9.5 Color Light gray* Solvent content None Data of the waterproofing membrane Water absorption 11% after 28 days Tensile strength 1 N\/mm² Elongation at break  600% Vapor diffusion equivalent 50 (m air layer thickness) Consumption * 1.2 kg\/m² for 600 µm dry film thickness  \u003c\/p\u003e\n\u003ch2\u003eSystem accessories for Silox 909 Pool MX - Liquid membrane for waterproofing concrete and screed\u003c\/h2\u003e\n\u003cp\u003eHydroFlex Sealing Tape 275 – Adhesive tape system for sealing joints and cracks Cembond M 947 flex – flexible sealing slurry for surface waterproofing Silipox 826 FlexBand Adhesive – Adhesive tape system for waterproofing \u003cstrong\u003eContainer: 30.3 kg\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan style=\"color: #ff0000;\"\u003eThe material is sensitive to frost and must not be transported or stored below \u0026lt; 5°C\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":62357905047882,"sku":"1064","price":355.4,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Abdichtung-Beschichtungen-DuroFlex-M-900-_E2_80_93-Flu_CC_88ssigfolie-zur-Abdichtung-von-Beton-und-Estrich-klein_209c7adf-68ef-4d19-b1ce-504bf33df5a0.jpg?v=1782831228"},{"product_id":"silox-903df-hochelastische-fluessigfolie-fuer-den-aussenbereich","title":"SILOX 903DF - Highly elastic liquid membrane for outdoor use","description":"\u003cp\u003eHighly elastic and crack-bridging liquid membrane for outdoor use \u003cstrong\u003eSILOX - 903 DF is a highly elastic coating. SILOX-903 coatings are stretchable, permanently bridge cracks, and are weather-resistant.\u003c\/strong\u003e SILOX-903 DF: The simple and reliable sealant for cracked concrete components:\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003efor flat roofs\u003c\/li\u003e\n\n\u003cli\u003efor facades and foundations\u003c\/li\u003e\n\n\u003cli\u003efor engineering structures!\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eCoatings made of Silox 903DF are waterproof, tough-elastic membranes with high tensile strength and excellent adhesion. After application, the product dries very quickly into a homogeneous, liquid-tight film (membrane) with very good resistance to alkalis, acids, UV light, and other weathering influences. SILOX-903DF sealing membranes are seamless, highly elastic, and bridge cracks in the substrate.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eFlexible and highly elastic\u003c\/li\u003e\n\n\u003cli\u003eCan also be applied to damp substrates\u003c\/li\u003e\n\n\u003cli\u003eContains no solvents\u003c\/li\u003e\n\n\u003cli\u003eBridges cracks and is dirt-repellent\u003c\/li\u003e\n\n\u003cli\u003eOutstanding substrate adhesion\u003c\/li\u003e\n\n\u003cli\u003eFast drying\u003c\/li\u003e\n\n\u003cli\u003eFiber-reinforced\u003c\/li\u003e\n\n\u003cli\u003eAlkali-resistant, also suitable for new concrete and fresh plaster\u003c\/li\u003e\n\n\u003cli\u003eSimple and easy to process\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eApplication is simple by rolling generously with plush rollers or by spraying, preferably using the airless method. Water is sufficient for cleaning tools and machinery. SILOX-903DF is viscous. It can be applied like emulsion paints, but it is better and more efficient to apply by spraying. For reliable protection of concrete surfaces, SILOX membranes should be at least 600 µm \/ 0.6 mm thick (dry), corresponding to a wet coating thickness of 1 mm and a consumption of 1200 grams per m2. For roof coatings and surfaces with dynamic cracks, dry film thicknesses of approx. 1200 µm are recommended. The coating should always be applied in at least two layers using a cross-coating technique to avoid gaps. Differentiating the color of the two layers allows for simple control over the uniform application of the coating; we therefore recommend always working in \"two colors.\" The substrate must be load-bearing, clean, and free of all separating substances. For concrete, blowholes, surface pores, cracks wider than 0.1 mm, breakouts, etc., must be repaired. Our SILOX cement fillers 962 or 963 are particularly well-suited for this work. Masonry surfaces must be clean and fully jointed, or they should (more reliably) either be plastered smooth* or covered with Cembond 947 elastic sealing slurry. It is recommended to prime new, smooth-formed concrete or plaster surfaces with a bonding agent; SILOX-856, a water-dilutable epoxy resin, is ideally suited as a primer. Always prime highly absorbent substrates to prevent the coating from \"burning\" (drying out too quickly). Expansion joints—e.g., at floor-wall connections, butt joints in precast concrete parts, etc.—can be additionally secured by embedding joint tapes to absorb larger movements in the substrate. The joint tape is glued on before coating and then finished over with the sealing membrane. For substrates heavily prone to cracking, it is also possible to easily embed commercially available glass or textile fiber reinforcement fleeces into the fresh SILOX-903 membrane for added strength.\u003c\/p\u003e\n\u003ch2\u003eSystem accessories for SILOX 903DF - Highly elastic liquid membrane for outdoor use\u003c\/h2\u003e\n\u003cp\u003eHydroFlex Sealing Tape 275 – adhesive film system for sealing joints and cracks; Cembond M 947 flex – flexible sealing slurry for surface waterproofing; Silipox 826 FlexBand Adhesive – adhesive film system for sealing \u003cstrong\u003eContents: 30 kg bucket\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan style=\"color: #ff0000;\"\u003eThe material is sensitive to frost and must not be transported or stored at temperatures below \u0026lt; 5°C\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"13 kg","offer_id":62357905113418,"sku":"1068","price":151.88,"currency_code":"EUR","in_stock":true},{"title":"30 kg","offer_id":62357905146186,"sku":"1069","price":357.11,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Silox-903-DF-Beschichtung-e1444302573335.jpg?v=1782831231"},{"product_id":"duroflex-primer-900-p1-primer-fuer-duroflex-und-silox-fluessigfolien-5-kg","title":"DuroFlex Primer 900-P1, primer for DuroFlex and Silox liquid membranes 5 kg","description":"DuroFlex Primer 900-P1 is a bonding agent for DuroFlex and Silox liquid membranes.\n\nAs with all coatings, proper substrate preparation is crucial.\nIt is generally recommended to prime new, smooth-formed concrete or plaster surfaces with\na bonding agent. Surfaces other than concrete require appropriately\nadapted primers. See types: Duroflex Primer P2 - P4.\n\nFor silage tanks and similarly demanding applications, we recommend DuroFlex Primer 900-P4.\n\n\u003ca href=\"https:\/\/shop.arcan.biz\/wp-content\/uploads\/2022\/02\/D-DuroFlex-Primer-900-P1-Feuchtraum.pdf\"\u003eD-DuroFlex Primer 900-P1 Wet Room\u003c\/a\u003e\n\nContainer size: 5 kg","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":62357906784586,"sku":"1101","price":44.73,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/Alfredo-Coating-Systems-RED-e1660301390501.png?v=1782831269"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/collections\/Kategorie-Fluessigfolie.png?v=1785358035","url":"https:\/\/shop.arcan.biz\/en\/collections\/flussigfolie-1.oembed","provider":"ARCAN GmbH Abdichtungen – Handwerkerstore","version":"1.0","type":"link"}