{"title":"Floor coating","description":"\u003ch2 class=\"MsoListParagraph\"\u003eFloor coating\u003c\/h2\u003e\n\n\u003cp class=\"MsoListParagraph\"\u003eCoatings provide reliable protection for surfaces against moisture, contamination, chemical influences, and mechanical stress. They extend the service life of structures and components and contribute to long-term value retention.\u003c\/p\u003e\n\n\u003cp class=\"MsoListParagraph\"\u003eARCAN offers high-performance coating systems for professional use in interior and exterior areas.\u003c\/p\u003e","products":[{"product_id":"silox-epw-856-transparentes-epoxyd-impraegniersiegel","title":"Silox EPW 856 – transparent epoxy impregnating sealer","description":"\u003cp\u003e\u003cstrong\u003eTransparent epoxy impregnating sealer for damp substrates\u003c\/strong\u003e SILOX Impregnating Sealer EPW-856 is a water-emulsified 2-component system based on a special epoxy resin and hardener compound. EPW-856 can be used to treat concrete surfaces by impregnation or sealing, significantly improving their performance characteristics. EPW-856 is also recommended as a primer and bonding agent under color-pigmented EP coatings using SILOX-EPW-857. Like all SILOX EPW grades, EPW-856 can be diluted with water. The resin is characterized by excellent adhesion - even on damp substrates.\u003c\/p\u003e\n\u003cp\u003eCured impregnations and sealers with SILOX-856 are not vapor-tight; therefore, the drying of treated concrete surfaces is not significantly hindered, and adhesion problems, blistering, or similar phenomena caused by the effect of water on the coating-to-substrate interface cannot occur. EPW-856 consists of two components that must be thoroughly mixed in a 2:1 ratio before processing. If necessary, this mixture can be further diluted with clean water to adjust the brushing or spraying viscosity.\u003c\/p\u003e\n\u003cp\u003eWhen using spraying equipment, care must be taken to ensure that the aerosols (spray mist) created - especially when spraying with high-pressure (airless) equipment - do not contaminate adjacent components. The quality of the dried coating films is so high that such contamination can hardly be removed. Due to the cross-linking reaction of the epoxy resin that begins immediately after mixing the components, the pot life of mixtures made from EPW 856 components is naturally limited. Higher temperatures additionally accelerate the setting reaction, as with all 2-component systems. Since the end of the pot life in water-emulsified epoxy systems is not recognizable by the typical increase in the mixture's viscosity, the pot life must be strictly monitored and adhered to. To avoid errors, it is recommended to always mix only as much material as can be easily processed within a manageable amount of time. The substrates must be clean, free of dust and other contaminants that could act as a release agent, and sufficiently load-bearing.\u003c\/p\u003e\n\u003cp\u003ePlease also observe the relevant technical standards for painting and coating work (e.g., DIN 18363 in Germany) and the ARCAN instruction sheet for the processing of SILOX-EPW products. Consumption naturally depends on the roughness and absorbency of the concrete. For machine-smoothed concrete floors and smooth-shuttered concrete surfaces, consumption values of approx. 100 - 200 g\/m² per application are to be expected, depending on the application method. Machines and tools can be cleaned with water with the addition of a commercially available wetting agent (dishwashing detergent). It is advisable to use hot water for this purpose. To safely prevent valves and delivery pistons in spraying units from sticking, we recommend flushing the equipment with water, then additionally flushing with our safety solvent HydroSolv-520, and finally filling with the maintenance agent HydroMoll-522 for storage preservation. Contamination by cured material is difficult to remove; therefore, we recommend protecting adjacent components by masking and covering them and always removing unavoidable spills immediately.\u003c\/p\u003e\n\u003ch2\u003eSystem accessories for Silox EPW 856 – transparent epoxy impregnating sealer\u003c\/h2\u003e\n\u003cp\u003eSilox EPW 857 – color-pigmented epoxy coating Silox Sealing Slurry 863 – universal sealing and coating compound \u003cstrong\u003eContents: Component A 5 kg, Component B 2.5 kg\u003c\/strong\u003e\u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"7.5 kg","offer_id":62357904687434,"sku":"1053","price":114.19,"currency_code":"EUR","in_stock":true},{"title":"15 kg","offer_id":62357904720202,"sku":"1054","price":212.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Abdichtung-Beschichtungen-transparentes-Epoxyd-Impra_CC_88gniersiegel-856.jpg?v=1782831215"},{"product_id":"silox-epw-857-in-ral-7030-farbig-pigmentierte-epoxydbeschichtung-35-68-kg","title":"Silox EPW 857 in RAL 7030 - colored epoxy coating (35.68 kg)","description":"\u003cp\u003e\u003cstrong\u003eColored pigmented epoxy coating for damp substrates\u003c\/strong\u003e EPW-857 is a water-emulsified, colored pigmented 2-component system based on a special epoxy resin and hardener compound. The product is recommended as an abrasion-resistant and highly chemical-resistant decorative protective coating for all mineral surfaces and also for mastic asphalt. Like all SILOX EPW grades, EPW-857 can be diluted with water. The coating is characterized by excellent adhesion - even on damp substrates. Cured coatings made of SILOX-857 are not vapor-tight; therefore, the drying out of treated concrete surfaces or water vapor diffusion from the substrate is not significantly obstructed, and adhesion failure, blistering, or similar damage due to water exposure at the coating-substrate interface cannot occur. Colored protective coatings for concrete surfaces in industry, in sewage treatment plants, as well as for garage and basement floors and similar areas of application. Durable protective coatings for walls that must be frequently decontaminated or cleaned with high-pressure water or steam jets, e.g., in tunnels, in food industry facilities, etc. EPW-857 consists of two components that must be thoroughly mixed in a mixing ratio of 2:1 before application. The mixture can then be diluted with clean water as needed to adjust the brushing or spraying viscosity.\u003c\/p\u003e\n\u003cp\u003eWhen using spraying equipment, ensure that aerosols (spray mist) generated—especially when spraying with high-pressure (airless) devices—do not contaminate adjacent components. The quality of the dried coating films is so high that such contamination can hardly be removed. Due to the cross-linking reaction of the epoxy binder that begins immediately after mixing the components, the pot life of the mixtures from the EPW 857 components is naturally limited. Higher temperatures additionally accelerate the setting reaction. Since the end of the pot life in water-emulsified epoxy systems of this type is \u003cu\u003enot\u003c\/u\u003e recognizable by the typical increase in the viscosity of the mixture, this property must be carefully observed. To avoid errors, it is recommended to mix only as much material as can be easily processed in a manageable time. Substrates must be clean and free of dust and other contaminants that act as release agents. They must have sufficient load-bearing capacity or be pretreated with a non-pigmented primer with sufficient penetration depth. Observe the relevant technical rules for painting and coating work (e.g., DIN 18363).\u003c\/p\u003e\n\u003cp\u003eConsumption is naturally dependent on the roughness depth and absorbency of the concrete. For machine-smoothed concrete floors and smooth-shuttered concrete surfaces, consumption values of approx. 150 - 300 g\/m\u003csup\u003e2\u003c\/sup\u003e per coat—depending on the application—are to be expected. Machines and tools can be cleaned with water with the addition of a commercial wetting agent (dish soap). It is advisable to use hot water for this purpose. To reliably prevent valves and feed pistons in spraying machines from sticking, we recommend flushing the equipment with our safety solvent HydroSolv-520 after rinsing with water and then filling it with HydroMoll 522 care agent for storage preservation. Contamination from cured material is difficult to remove; we therefore recommend protecting adjacent components by masking and covering them, and always removing unavoidable impurities immediately.\u003c\/p\u003e\n\u003ch2\u003eSystem accessories for Silox EPW 857 in RAL 7030 - colored pigmented epoxy coating\u003c\/h2\u003e\n\u003cp\u003eSilox EPW 856 – transparent epoxy impregnating sealer; Silox Sealing Slurry 863 – universal sealing and coating compound\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eContents:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003e5.96 kg container: follows shortly\u003c\/li\u003e\n\n\u003cli\u003e35.68 kg container: A component 29.94 kg, B component 5.74 kg\u003cstrong\u003e\u003cbr\u003e\u003c\/strong\u003e\n\n\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"ARCAN","offers":[{"title":"5.96 kg","offer_id":62887813382474,"sku":"1056","price":109.21,"currency_code":"EUR","in_stock":true},{"title":"35.68 kg","offer_id":62887813415242,"sku":"1055","price":549.85,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Beschichtungen-_C2_BB-Garagensiegel-_C2_BB-Silox-EPW-857-in-RAL-7032-e1445430295538.jpg?v=1782831215"},{"product_id":"silox-epw-857-in-ral-7032-farbig-pigmentierte-epoxydbeschichtung-35-68-kg","title":"Silox EPW 857 in RAL 7032 - colored epoxy coating (35.68 kg)","description":"\u003cstrong\u003eColored pigmented epoxy coating for damp substrates\u003c\/strong\u003e\n\nEPW-857 is a water-emulsified, colored pigmented 2-component system based on a special epoxy resin and hardener compound. The product is recommended as an abrasion-resistant, chemically resistant, and decorative protective coating for all mineral surfaces as well as mastic asphalt.\n\nLike all SILOX EPW grades, EPW-857 can be diluted with water. The coating is characterized by excellent adhesion - even on damp substrates.\n\nCured coatings made of SILOX-857 are not vapor-tight; therefore, the drying of treated concrete surfaces or water vapor diffusion from the substrate is not significantly hindered, and adhesion problems, blistering, or similar damage caused by water acting on the coating-substrate interface cannot occur.\n\nColored protective coatings for concrete surfaces in industry, sewage treatment plants, as well as for garage and basement floors and similar application areas. Durable protective coatings for walls that must be frequently decontaminated or cleaned with high-pressure water or steam jets, e.g., in tunnels, in the food processing industry, etc.\n\nEPW-857 consists of two components, which must be thoroughly mixed in a mixing ratio of 2:1 before application. The mixture can then be diluted with clean water if necessary to adjust the brushing or spraying viscosity. When using spraying equipment, ensure that aerosols (spray mist) – especially those generated when spraying with high-pressure (airless) equipment – do not contaminate adjacent components. The quality of the dried coating films is so high that such contamination can hardly be removed.\n\nDue to the cross-linking reaction of the epoxy binder that begins immediately after mixing the components, the pot life of the mixtures of the EPW-857 components is naturally limited. Higher temperatures additionally accelerate the setting reaction. Since the end of the pot life of water-emulsified epoxy systems of this type is \u003cu\u003enot\u003c\/u\u003e recognizable by the typical increase in the viscosity of the mixture, this property must be carefully observed. To avoid errors, it is recommended to mix only as much material as can be easily applied within a reasonable amount of time.\n\nThe substrates must be clean and free of dust and other substances that have a separating effect. They must have sufficient load-bearing capacity or be pre-treated with a non-pigmented primer with sufficient penetration. Please observe the relevant technical rules for painting and coating work (e.g., DIN 18363).\n\nConsumption naturally depends on the roughness and absorbency of the concrete. For machine-smoothed concrete floors and smooth shuttered concrete surfaces, consumption values of approx. 150 - 300 g\/m\u003csup\u003e2\u003c\/sup\u003e per application are to be expected, depending on the application method.\u003cstrong\u003e \u003c\/strong\u003e\n\nMachines and tools can be cleaned with water supplemented with a standard wetting agent (dishwashing detergent). It is advisable to use hot water for this purpose.\n\nTo reliably prevent valves and delivery pistons in spray machines from sticking, we recommend flushing the equipment with water, then additionally flushing it with our safety solvent HydroSolv-520, and finally filling it with HydroMoll 522 care agent for storage preservation.\n\nContamination from cured material is difficult to remove; we therefore recommend protecting adjacent components by masking and covering them and always removing unavoidable contamination immediately.\n\u003ch2\u003eSystem accessories for Silox EPW 857 in RAL 7032 - colored pigmented epoxy coating\u003c\/h2\u003e\nSilox EPW 856 – transparent epoxy impregnation sealer\n\n Silox Sealing Slurry 863 – universal sealing and coating compound\n\n\u003cstrong\u003eContent: A component 29.94 kg, B component 5.74 kg\u003c\/strong\u003e","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":62357904785738,"sku":"1056","price":485.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Beschichtungen-_C2_BB-Garagensiegel-_C2_BB-Silox-EPW-857-in-RAL-7032-e1445430295538_4e18643b-2b6c-41c6-b35d-f05916511f14.jpg?v=1782831216"},{"product_id":"duroflex-m-900-fluessigfolie-zur-abdichtung-von-beton-und-estrich","title":"DuroFlex M 900 - Liquid membrane for sealing concrete and screed","description":"\u003cp\u003e\u003cb\u003e\u003cb\u003eLiquid foil for waterproofing concrete \u003c\/b\u003e\u003c\/b\u003e DuroFlex - 900M is a highly efficient protective coating for concrete against the aggressive components of silage. The product consists of only one component and is easy and trouble-free to apply.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eSilage containers\u003c\/li\u003e\n\n\u003cli\u003eWet rooms (bathrooms)\u003c\/li\u003e\n\n\u003cli\u003eBalconies (under the final surface)\u003c\/li\u003e\n\n\u003cli\u003eTerraces (under the final surface)\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eSilage – green fodder prepared by fermentation – is produced by the fermentation of plants in the absence of air. Fermentation is a form of lactic acid fermentation. Unavoidable by-products of this process are acidic, aqueous leachates that contain lactic acid, but also butyric acid and acetic acid. These organic acids are extremely aggressive; they attack concrete surfaces and destroy them upon prolonged contact. The leachate escaping from silage silos also contaminates the groundwater. By coating with DuroFlex-900M, which was specially developed for this application, concrete components are safely protected and sealed against silage runoff. DuroFlex-900M is an emulsion of a self-crosslinking, rubber-like polymer, acid-resistant silicate fillers, color pigments, additives, and water. After application, the product dries very quickly into a homogeneous, liquid-tight foil (membrane) with very good resistance to alkalis, acids, and weather influences. Sealing foils made of DuroFlex-900M are seamless and jointless, highly elastic, and bridge cracks in the substrate.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eResistant to silage components\u003c\/li\u003e\n\n\u003cli\u003eFlexible and highly elastic\u003c\/li\u003e\n\n\u003cli\u003eCan also be applied to damp substrates\u003c\/li\u003e\n\n\u003cli\u003eHigh abrasion resistance\u003c\/li\u003e\n\n\u003cli\u003eContains no solvents\u003c\/li\u003e\n\n\u003cli\u003eBridges cracks and is dirt-repellent\u003c\/li\u003e\n\n\u003cli\u003eExcellent adhesion to concrete\u003c\/li\u003e\n\n\u003cli\u003eFast drying\u003c\/li\u003e\n\n\u003cli\u003eAlkali-resistant, also suitable for new concrete and fresh plaster\u003c\/li\u003e\n\n\u003cli\u003eEasy and trouble-free to apply\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eDuroFlex-900M is ready to use, with a thick, slightly thixotropic consistency. It can be applied like conventional dispersion paints, but it is better and more efficient to apply it by spraying. For reliable protection of concrete surfaces, DuroFlex membranes should be at least 600 µm \/ 0.6 mm thick (dry), corresponding to a wet coating thickness of 1 mm and a consumption of 1200 grams per m2. The coating should always be applied in two layers and in a cross-pattern to avoid defects. Different coloring of the two layers allows easy control over the even application of the coating; we therefore recommend always working in \"two colors\". The substrate must be load-bearing, clean, and free of all substances that could act as release agents. For concrete, voids, air pores in the surface, cracks over 0.1 mm wide, breakages, etc., must be repaired. UP Stone Filler 1013 is particularly suitable for this work. Masonry surfaces must be clean and fully jointed, or (for safety) either plastered smooth* or coated with an elastic sealing slurry*. * Cement plaster of mortar group III, expediently treated with SILEX-956 * SILEX-947 (highly elastic organomineral sealing slurry) It is recommended to prime new, smooth-formed concrete or plaster surfaces with an adhesive primer. For silage containers and similar demanding applications, we recommend Silox EPW-856; for simpler applications, DuroFlex 900-P Primer is suitable. Always prime highly absorbent substrates to prevent the coating from \"burning\" (drying too fast). If necessary, DuroFlex-900 M can be diluted with water (up to 10%, e.g., to adjust the spray viscosity). To improve abrasion resistance and for a non-slip surface, sharp-washed quartz sand – grain size e.g., 0.3 - 0.6 mm – can be mixed into the first DuroFlex coating or the freshly applied coating can be dusted with it. DuroFlex-900M must not be used at temperatures below 7°C, or in rain or extremely high humidity. Intermediate coats must be completely dry before applying the top coat to prevent dry cracks in the coating surface due to tension. Working joints – e.g., at floor-wall connections, butt joints in precast concrete parts – can be additionally secured by embedding HydroFlex 275, a special joint tape, to absorb larger movements in the substrate. The joint tape is glued on before coating and then covered with the sealing foil. For substrates heavily prone to cracks, it is possible to easily embed commercially available reinforcing fleece made of glass or textile fibers into the DuroFlex membrane for reinforcement. Product in delivery form Binder Emulsion of butadiene rubber (SBR) Density Approx. 1.2 g\/ml at 20° Viscosity Thixotropic Odor Faint, specific to butadiene rubber pH Approx. 9.5 Color Light gray* Solvent content None Characteristic data of the sealing foil Water absorption 11% after 28 days Tensile strength 1 N\/mm² Elongation at break ≥ 600% Vapor diffusion equivalent 50 (m air layer thickness) Consumption * 1.2 kg \/ m² for 600 µm dry film thickness \u003c\/p\u003e\n\u003ch2\u003eSystem accessories for DuroFlex M 900 - Liquid foil for waterproofing concrete and screed\u003c\/h2\u003e\n\u003cp\u003eHydroFlex Sealing Tape 275 – Adhesive foil system for sealing joints and cracks Cembond M 947 flex – flexible sealing slurry for surface waterproofing Silipox 826 FlexBand Adhesive – Adhesive foil system for sealing \u003cstrong\u003eContents: 30 kg bucket\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan style=\"color: #ff0000;\"\u003eThe material is sensitive to frost and must not be transported or stored at temperatures below 5°C\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"13 kg","offer_id":62357904884042,"sku":"1057","price":154.12,"currency_code":"EUR","in_stock":true},{"title":"30 kg","offer_id":62357904916810,"sku":"1058","price":343.07,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Abdichtung-Beschichtungen-DuroFlex-M-900-_E2_80_93-Fl_C3_BCssigfolie-zur-Abdichtung-von-Beton-und-Estrich-klein.jpg?v=1782831219"},{"product_id":"silox-909-pool-mx-fluessigfolie-zur-abdichtung-von-schwimmbecken","title":"Silox 909 Pool MX - Liquid membrane for swimming pool waterproofing (30.3 kg)","description":"\u003cp\u003e\u003cb\u003eLiquid membrane for waterproofing concrete swimming pools\u003c\/b\u003e Silox 909 Pool Mx is an elastic liquid membrane for concrete, used for waterproofing against water. The product consists of 2 components that are mixed together. It is simple and easy to apply.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eConcrete swimming pools\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eConcrete components are waterproofed by applying a coating of Silox Pool 909 MX, which was specially developed for this application. Silox Pool 909 MX is an emulsion of a self-crosslinking, rubber-like polymer, acid-resistant silicate fillers, color pigments, additives, and water. After application, the product dries very quickly into a homogeneous, liquid-tight film (membrane) with very good resistance. Silox 909 MX waterproofing membranes are seamless and jointless, highly elastic, and bridge cracks in the substrate.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eFlexible and highly elastic\u003c\/li\u003e\n\n\u003cli\u003eCan also be applied to damp substrates\u003c\/li\u003e\n\n\u003cli\u003eHigh abrasion resistance\u003c\/li\u003e\n\n\u003cli\u003eSolvent-free\u003c\/li\u003e\n\n\u003cli\u003eBridges cracks\u003c\/li\u003e\n\n\u003cli\u003eExcellent adhesion to concrete\u003c\/li\u003e\n\n\u003cli\u003eFast drying (depends on weather conditions and layer thickness)\u003c\/li\u003e\n\n\u003cli\u003eAlkali-resistant, also suitable for new concrete and fresh plaster\u003c\/li\u003e\n\n\u003cli\u003eSimple and easy to apply\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eSilox 909 Pool is ready to use and has a thick, slightly thixotropic consistency. It can be applied like conventional emulsion paints by brushing, though spraying is better and more efficient. For secure protection of concrete surfaces, Silox membranes should be at least 600 µm \/ 0.6 mm thick (dry), corresponding to a wet coating thickness of 1 mm and a consumption of 1200 grams per m2. The coating should always be applied in two layers and in a cross-pattern to avoid voids. Using different colors for the two layers allows for easy monitoring of uniform application, which is why we recommend always working with \"two colors\". The substrate must be load-bearing, clean, and free of all separating substances. For concrete, surface cavities, air pores, cracks wider than 0.1 mm, breakouts, etc., must be repaired. UP Stone Filler 1013 is particularly well-suited for this work. Masonry surfaces must be clean and fully pointed, or (for greater security) they must be plastered smooth* or covered with an elastic sealing slurry*. * Cement plaster of mortar group III, appropriately treated with SILEX-956 * SILEX-947 (highly elastic organo-mineral sealing slurry) We recommend priming new, smooth-formed concrete or plaster surfaces with a bonding agent. For this, we recommend Silox EPW-856; for simpler applications, DuroFlex 900-P Primer is suitable. Always prime highly absorbent substrates to prevent the coating from burning. If necessary, Silox 909 can be diluted with water (up to 10%, e.g., to adjust spray viscosity). To improve abrasion resistance and provide a non-slip surface, either sharp-washed quartz sand (grain size e.g., 0.3 - 0.6 mm) can be mixed into the first DuroFlex coating, or the freshly applied coating can be blinded with it. Silox 909 must not be applied at temperatures below 7°C, in rain, or in extremely high humidity. Intermediate layers must be completely dry before applying the topcoat to ensure that no drying cracks form in the surface of the coating due to tension. The primer must also be completely dry before applying the subsequent coating. Construction joints – e.g., at floor-to-wall connections or joint gaps in precast concrete components – can be additionally secured by embedding HydroFlex 275, a special joint tape, to absorb larger movements in the substrate. The joint tape is adhered before coating and then covered with the waterproofing membrane. For substrates at high risk of cracking, it is possible to embed standard glass or textile fiber reinforcement fleeces into the membrane for reinforcement without difficulty. Product as supplied Binder Emulsion of butadiene rubber (SBR) Density Approx. 1.2 g\/ml at 20° Viscosity Thixotropic Odor Faint, specific to butadiene rubber pH Approx. 9.5 Color Light gray* Solvent content None Data of the waterproofing membrane Water absorption 11% after 28 days Tensile strength 1 N\/mm² Elongation at break  600% Vapor diffusion equivalent 50 (m air layer thickness) Consumption * 1.2 kg\/m² for 600 µm dry film thickness  \u003c\/p\u003e\n\u003ch2\u003eSystem accessories for Silox 909 Pool MX - Liquid membrane for waterproofing concrete and screed\u003c\/h2\u003e\n\u003cp\u003eHydroFlex Sealing Tape 275 – Adhesive tape system for sealing joints and cracks Cembond M 947 flex – flexible sealing slurry for surface waterproofing Silipox 826 FlexBand Adhesive – Adhesive tape system for waterproofing \u003cstrong\u003eContainer: 30.3 kg\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan style=\"color: #ff0000;\"\u003eThe material is sensitive to frost and must not be transported or stored below \u0026lt; 5°C\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":62357905047882,"sku":"1064","price":355.4,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Abdichtung-Beschichtungen-DuroFlex-M-900-_E2_80_93-Flu_CC_88ssigfolie-zur-Abdichtung-von-Beton-und-Estrich-klein_209c7adf-68ef-4d19-b1ce-504bf33df5a0.jpg?v=1782831228"},{"product_id":"silox-903df-hochelastische-fluessigfolie-fuer-den-aussenbereich","title":"SILOX 903DF - Highly elastic liquid membrane for outdoor use","description":"\u003cp\u003eHighly elastic and crack-bridging liquid membrane for outdoor use \u003cstrong\u003eSILOX - 903 DF is a highly elastic coating. SILOX-903 coatings are stretchable, permanently bridge cracks, and are weather-resistant.\u003c\/strong\u003e SILOX-903 DF: The simple and reliable sealant for cracked concrete components:\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003efor flat roofs\u003c\/li\u003e\n\n\u003cli\u003efor facades and foundations\u003c\/li\u003e\n\n\u003cli\u003efor engineering structures!\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eCoatings made of Silox 903DF are waterproof, tough-elastic membranes with high tensile strength and excellent adhesion. After application, the product dries very quickly into a homogeneous, liquid-tight film (membrane) with very good resistance to alkalis, acids, UV light, and other weathering influences. SILOX-903DF sealing membranes are seamless, highly elastic, and bridge cracks in the substrate.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eFlexible and highly elastic\u003c\/li\u003e\n\n\u003cli\u003eCan also be applied to damp substrates\u003c\/li\u003e\n\n\u003cli\u003eContains no solvents\u003c\/li\u003e\n\n\u003cli\u003eBridges cracks and is dirt-repellent\u003c\/li\u003e\n\n\u003cli\u003eOutstanding substrate adhesion\u003c\/li\u003e\n\n\u003cli\u003eFast drying\u003c\/li\u003e\n\n\u003cli\u003eFiber-reinforced\u003c\/li\u003e\n\n\u003cli\u003eAlkali-resistant, also suitable for new concrete and fresh plaster\u003c\/li\u003e\n\n\u003cli\u003eSimple and easy to process\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eApplication is simple by rolling generously with plush rollers or by spraying, preferably using the airless method. Water is sufficient for cleaning tools and machinery. SILOX-903DF is viscous. It can be applied like emulsion paints, but it is better and more efficient to apply by spraying. For reliable protection of concrete surfaces, SILOX membranes should be at least 600 µm \/ 0.6 mm thick (dry), corresponding to a wet coating thickness of 1 mm and a consumption of 1200 grams per m2. For roof coatings and surfaces with dynamic cracks, dry film thicknesses of approx. 1200 µm are recommended. The coating should always be applied in at least two layers using a cross-coating technique to avoid gaps. Differentiating the color of the two layers allows for simple control over the uniform application of the coating; we therefore recommend always working in \"two colors.\" The substrate must be load-bearing, clean, and free of all separating substances. For concrete, blowholes, surface pores, cracks wider than 0.1 mm, breakouts, etc., must be repaired. Our SILOX cement fillers 962 or 963 are particularly well-suited for this work. Masonry surfaces must be clean and fully jointed, or they should (more reliably) either be plastered smooth* or covered with Cembond 947 elastic sealing slurry. It is recommended to prime new, smooth-formed concrete or plaster surfaces with a bonding agent; SILOX-856, a water-dilutable epoxy resin, is ideally suited as a primer. Always prime highly absorbent substrates to prevent the coating from \"burning\" (drying out too quickly). Expansion joints—e.g., at floor-wall connections, butt joints in precast concrete parts, etc.—can be additionally secured by embedding joint tapes to absorb larger movements in the substrate. The joint tape is glued on before coating and then finished over with the sealing membrane. For substrates heavily prone to cracking, it is also possible to easily embed commercially available glass or textile fiber reinforcement fleeces into the fresh SILOX-903 membrane for added strength.\u003c\/p\u003e\n\u003ch2\u003eSystem accessories for SILOX 903DF - Highly elastic liquid membrane for outdoor use\u003c\/h2\u003e\n\u003cp\u003eHydroFlex Sealing Tape 275 – adhesive film system for sealing joints and cracks; Cembond M 947 flex – flexible sealing slurry for surface waterproofing; Silipox 826 FlexBand Adhesive – adhesive film system for sealing \u003cstrong\u003eContents: 30 kg bucket\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan style=\"color: #ff0000;\"\u003eThe material is sensitive to frost and must not be transported or stored at temperatures below \u0026lt; 5°C\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"13 kg","offer_id":62357905113418,"sku":"1068","price":151.88,"currency_code":"EUR","in_stock":true},{"title":"30 kg","offer_id":62357905146186,"sku":"1069","price":357.11,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Silox-903-DF-Beschichtung-e1444302573335.jpg?v=1782831231"},{"product_id":"671-1l","title":"DuroFlex 671 - universal primer for mineral substrates and asphalt 1 liter","description":"\u003cp class=\"Normal tm5\"\u003e\u003cspan class=\"tm6\"\u003e1-component primer and impregnating sealer for concrete and asphalt\u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"Normal tm5\"\u003e\u003cstrong\u003e\u003cspan class=\"tm6\"\u003eDuroFlex 671 is a ready-to-use polyurethane coating material. The product cures through reaction with traces of atmospheric moisture to form elastic, durable layers with excellent adhesion to almost any substrate.\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp class=\"Normal tm5\"\u003e\u003cspan class=\"tm7\"\u003eDue to its excellent substrate adhesion, \u003c\/span\u003e\u003cspan class=\"tm8\"\u003eDuroFlex 671\u003c\/span\u003e\u003cspan class=\"tm7\"\u003e is perfectly suited as a bonding agent for subsequent coatings, preferably on difficult, bituminous-bound substrates. Such surfaces can also be sealed through a double or multiple treatment with \u003c\/span\u003e\u003cspan class=\"tm8\"\u003eDuroFlex 671\u003c\/span\u003e\u003cspan class=\"tm7\"\u003e and protected against wear and, to a limited extent, even against the effects of oil and fuels. \u003c\/span\u003e\u003cspan class=\"tm7\"\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"Normal tm5\"\u003e\u003cspan class=\"tm7\"\u003eSealers with \u003c\/span\u003e\u003cspan class=\"tm8\"\u003eDuroFlex 671\u003c\/span\u003e\u003cspan class=\"tm7\"\u003e are satin to glossy and dry clear. The films provide excellent surface protection and are abrasion-resistant.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"Normal tm5\"\u003e\u003cspan class=\"tm7\"\u003e\u003cstrong\u003eContent: \u003c\/strong\u003e1 liter\u003c\/span\u003e\u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":62833237688650,"sku":"1198","price":17.82,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/Bild1.jpg?v=1787841535"},{"product_id":"blocsil-790-integral-5-kg","title":"BlocSil 790 Integral - transparent sealant with UV protection","description":"\u003cp\u003e\u003cstrong\u003eHighly abrasion-resistant, self-crosslinking methacrylate sealer\u003c\/strong\u003e \u003cbr\u003eBlocSil-790 is a chemically reactive yet single-component product that can be used to create wear-resistant, transparent protective coatings (sealers). BlocSil-790 can be diluted with water. Films made from BlocSil-790 integral are very hard, abrasion-resistant, transparent, weather-resistant, and—typical of methacrylates—also resistant to UV radiation, meaning they do not yellow. It also features exceptionally high resistance to plasticizer migration. Car tires—even hot, wet tires (!) —leave no marks on BlocSil-790. The outstanding adhesion and resistance to environmental influences and many chemicals make BlocSil 790i the material of choice for\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eprotecting concrete floors, screeds, and terrazzo\u003c\/li\u003e\n\n\u003cli\u003eprotecting natural and artificial stone floor coverings\u003c\/li\u003e\n\n\u003cli\u003eprotecting terracotta floors\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eagainst wear, stains, and damage caused by de-icing salts and other aggressive pollutants. Application is simple. BlocSil-790i is ready to use and can be brushed, rolled, or sprayed on. The substrate must be clean and free of release agents. Absorbent substrates should be primed. For this purpose, BlocSil-790i diluted with 20–30% water is used as a base coat. On smooth, dense substrates, one coat is generally sufficient; for higher requirements regarding the wear resistance of the coating and a pore-free, dense film, two (or more) layers can be applied. BlocSil-790 integral dries physically at first—through the evaporation of the water contained in the product. The drying time is short but depends on the temperature, humidity, and the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIMPORTANT:\u003c\/strong\u003e \u003cbr\u003eAlong with the film formation that occurs during drying, the binder then crosslinks, thereby achieving its high level of performance. This reaction is of no consequence for subsequent coats of the same product; there are no adhesion issues during longer waiting times between individual work steps. Tools, equipment, and fresh residues of BlocSil-790 can be cleaned with water; adding 2–3% of a standard dishwashing detergent is helpful. Composition Polymethacrylates, additives, and auxiliaries Solvent Water Solids content approx. 40% Density approx. 1.03 g\/ml Appearance milky liquid Film properties hard, clear, glossy, transparent \u003cstrong\u003e  \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eConsumption\u003cbr\u003e\u003c\/strong\u003e100 - 150 g\/m\u003csup\u003e2\u003c\/sup\u003e (on smooth, dense substrates) The product must be stored in a way that it is inaccessible to unauthorized third parties and children. It becomes unusable if exposed to frost. Recommended storage temperatures are +5° to +30° C. In its original sealed container, BlocSil-790 has a shelf life of at least 18 months; opened containers should always be tightly sealed immediately after product removal and used within 8 weeks.\u003c\/p\u003e\n\u003ch2\u003eSystem accessories for BlocSil 790 Integral - transparent sealer with UV protection\u003c\/h2\u003e\n\u003cp\u003eStein Rein 915 – highly effective cleaning concentrate\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eContents: \u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003e1 kg\u003c\/li\u003e\n\n\u003cli\u003e5 kg\u003c\/li\u003e\n\n\u003cli\u003e10 kg\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"ARCAN","offers":[{"title":"1 kg","offer_id":62887912636746,"sku":"1202","price":15.36,"currency_code":"EUR","in_stock":true},{"title":"5 kg","offer_id":62887912669514,"sku":"1203","price":68.32,"currency_code":"EUR","in_stock":true},{"title":"10 kg","offer_id":62887912702282,"sku":"1204","price":123.74,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/ARCAN-Bauchemie-Beschichtungen-_C2_BB-Versiegelung-_C2_BBBlocsil-790-Integral-e1445428841890.jpg?v=1787841540"},{"product_id":"silox-dichtschlaemme-863-in-farbe-blaugruen-universelle-abdichtungs-und-beschichtungsmasse-40-kg-grau","title":"Silox Sealing Slurry 863 – universal sealing and coating compound","description":"\u003cp\u003e\u003cstrong\u003eSpecial coloring for water basins\u003c\/strong\u003e - \u003cstrong\u003eSilox 863\u003c\/strong\u003e is a universal sealing and coating compound for all cement-bound building materials. \u003cstrong\u003eSilox 863\u003c\/strong\u003e is absolutely watertight yet vapor-permeable, can be applied to damp substrates, and withstands high water pressure. \u003cstrong\u003eSilox 863\u003c\/strong\u003e is sag-resistant and very tacky, making it easy to work with even on uneven walls with deep surface textures or overhead. \u003cstrong\u003eSilox 863\u003c\/strong\u003e adheres excellently to damp, mineral substrates and metals. If the substrate is clean and load-bearing, no special primers or base coats are necessary. Voids and pore-free coatings are absolutely liquid-tight yet vapor-permeable. Its excellent mechanical properties (hardness, abrasion resistance) also make it suitable for sealing floor surfaces - e.g., in basements and underground parking garages. \u003cstrong\u003eSilox 863\u003c\/strong\u003e can also be used for reprofiling damaged concrete surfaces, wet-on-wet, as a bonding bridge between old and new concrete, as an adhesive for natural and artificial stone, as an anchor mortar, and for similar applications.\u003c\/p\u003e\n\u003ch4\u003eSubstrate requirements\u003c\/h4\u003e\n\u003cp\u003eThe substrate must be clean and free of separating substances or coatings. Mineral substrates must be sufficiently firm and load-bearing; the tensile strength should not fall below 1.5 N\/mm² across the entire surface. Laitance layers on concrete and screed must be removed, and voids and pores must be opened. Iron and steel must be descaled to a bright metallic finish (SA 2½); mill scale and rust must be removed. \u003cstrong\u003eSilox 863\u003c\/strong\u003e is not suitable for plastics or substrates bonded with bitumen, asphalt, or tar.\u003c\/p\u003e\n\u003ch4\u003eMixing\u003c\/h4\u003e\n\u003cp\u003eEmpty component A completely into the container of component B and stir with a mixing machine until the color of the mixture is uniform and streak-free. Then, transfer the mixture as usual and stir thoroughly once more. Do not stir in air! The mixture stiffens significantly during the mixing process and becomes tacky and plastic. This effect is typical for the product and supports the exceptionally good sag resistance of \u003cstrong\u003eSilox 863\u003c\/strong\u003e on vertical surfaces and smooth substrates. By adding a little water - \u003cstrong\u003ea maximum of 5% - the mixture becomes more fluid but remains sufficiently sag-resistant\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch4\u003eApplication\u003c\/h4\u003e\n\u003cp\u003eSilox 863 is applied manually with standard tools (spatula, float, trowel, notched trowel) and can also be sprayed like thin-layer plasters or sealing slurries using light spraying machines (screw pumps). Depending on the spray pressure and the supporting air volume, this produces more or less finely textured, uniform surfaces.\u003c\/p\u003e\n\u003ch4\u003eCleaning\u003c\/h4\u003e\n\u003cp\u003eMachines and tools are cleaned with water - ideally with a little dish soap added. Fresh contamination from the material should also be removed by washing with water.\u003c\/p\u003e\n\u003ch4\u003ePot life\u003c\/h4\u003e\n\u003cp\u003eThe pot life of a mixture that has not been additionally diluted with water is approx. 30 - 40 minutes at 20°C. In the case of strong air movement or direct sunlight, a type of skin may form on the surface of freshly applied layers sooner. Such areas should no longer be reworked by smoothing.\u003c\/p\u003e\n\u003ch4\u003eSubsequent coatings\u003c\/h4\u003e\n\u003cp\u003eCoatings made of Silox 863 can be recoated with themselves or with vapor-permeable EP sealers (SILOX-857) after a waiting period of 24 hours. For vapor-tight topcoats, a waiting period of 96 hours (at 20°C) is recommended.\u003c\/p\u003e\n\u003ch4\u003eBoundary conditions\u003c\/h4\u003e\n\u003cp\u003eThe minimum temperature of the substrates should not fall below +9°C. The product must not be applied to glossy wet surfaces. To prevent \"burning\" on highly absorbent surfaces, dampen such areas before application or, better yet, prime them with Silox-856. Color: dark gray. Tested up to 7 bar negative water pressure!\u003c\/p\u003e\n\u003ch4\u003eContainers\/Variants:\u003c\/h4\u003e\n\u003cul\u003e\n\n\u003cli\u003e40.0 kg blue-green - contains total A and B components\u003c\/li\u003e\n\n\u003cli\u003e40.0 kg white - contains total A and B components\u003c\/li\u003e\n\n\u003cli\u003e40.0 kg gray - contains total A and B components\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"ARCAN","offers":[{"title":"40 kg blue-green","offer_id":62833258398026,"sku":"1209","price":631.13,"currency_code":"EUR","in_stock":true},{"title":"40 kg gray","offer_id":62833258430794,"sku":"1210","price":473.0,"currency_code":"EUR","in_stock":true},{"title":"40 kg white","offer_id":62833258463562,"sku":"1211","price":517.83,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/Cembond-863-Myria-Resort.jpg?v=1787841544"},{"product_id":"steinteppich","title":"Silibond S-990 binder for stone carpets","description":"\u003cp\u003eSILIBOND-990 is a pre-polymerized, reactive urethane resin with low viscosity. The product is a ready-to-use binder for dry sands and grit. The resin is completely lightfast, making it perfect as a binder for pure white sands made of marble, granite, and similar light-colored aggregates!\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eFast and reliable curing\u003c\/li\u003e\n\n\u003cli\u003eHigh strength, similar to epoxy resins\u003c\/li\u003e\n\n\u003cli\u003eSolvent-free\u003c\/li\u003e\n\n\u003cli\u003eNo yellowing, even under intense sunlight\u003c\/li\u003e\n\n\u003cli\u003ePre-formulated, easy to use\u003c\/li\u003e\n\n\u003cli\u003eLow viscosity, easy to mix, and non-sticky\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eSILIBOND S-990 is an ideal binder for water-permeable, highly decorative joint mortars made from coarse sands, as well as for decorative stone carpets made of marble, granite granulates, or colored quartz.\u003c\/p\u003e\n\u003cp\u003eSILIBOND-990 cures through reaction with the moisture naturally present in the air.\u003c\/p\u003e\n\u003cp\u003eThe mineral aggregates used must be dry. For water-permeable mortars (drainage mortars), the aggregates should not contain any fine dust and should be sufficiently coarse.\u003c\/p\u003e\n\u003cp\u003eThe binder requirement for water-permeable joint mortars or sand carpets is low. It depends on the particle size distribution and grain shape of the aggregates and the desired strength. For a typical high-strength drainage mortar, sands with grain sizes between 0.2 and 0.7 mm are recommended.\u003c\/p\u003e\n\u003cp\u003eAn ideal ratio is 3 to 5% S-990 binder to 100 parts aggregate, depending on the grain distribution (and thus the surface area) of the aggregates. A binder content that is too high can lead to curing issues and even cause blistering, while a binder content that is too low will inevitably reduce the mechanical strength of the cured mortar.\u003c\/p\u003e\n\u003cp\u003eTo prepare the mortar, the binder is mixed homogeneously with the aggregates. It is advisable to use forced-action mixers. Conventional free-fall mixers for cement mortar are not suitable. The mixing time itself is short but depends on the performance of the mixer used. Ready-to-use mixtures are only slightly damp. They are installed immediately, are not sticky, and are easy to level, smooth, and compact. Mortars made from SILIBOND S-990 can also be installed at low temperatures. Compared to epoxy resin mortars, they still cure perfectly under these conditions, which are typically difficult for reactive resins.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eCuring time\u003c\/strong\u003e (in mm thickness)\u003cbr\u003e23°C 15°C 10°C 5°C\u003cbr\u003e8 hours 11 9 6 3\u003cbr\u003e24 hours 25 18 12 8\u003cbr\u003e2 days 40 35 30 20\u003cbr\u003e2 \/3\u003cbr\u003e\u003cstrong\u003eProperties:\u003c\/strong\u003e Composition urethane polymer with NCO groups\u003cbr\u003e\u003cstrong\u003eForm of delivery: \u003c\/strong\u003eLiquid, ready-to-use\u003cbr\u003e\u003cstrong\u003eColor:\u003c\/strong\u003e Colorless, water-clear\u003cbr\u003e\u003cstrong\u003eOdor:\u003c\/strong\u003e Mild, characteristic of the product\u003cbr\u003e\u003cstrong\u003eViscosity:\u003c\/strong\u003e at 20° approx. 800 - 900 mPa.s\u003cbr\u003e\u003cstrong\u003eDensity:\u003c\/strong\u003e at 20° approx. 1.10 - 1.14 g\/ml\u003cbr\u003e\u003cbr\u003eMechanical properties (DIN 1164)\u003cbr\u003e- Mortar made of 100 parts by weight quartz sand 0.2 - 0.7 mm + 5 parts by weight SILIBOND 990 -\u003cbr\u003eCompressive strength approx. 40 N\/mm2\u003cbr\u003eFlexural strength approx. 20 N\/mm2\u003cbr\u003eModulus of elasticity\/flexural test approx. 8000 N\/mm2\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eSILIBOND S-990 is not flammable, but it is combustible. The product should be protected from fire or radiant heat, stored in a cool, dry place, and kept out of reach of children and unauthorized third parties.\u003c\/p\u003e\n\u003cp\u003eOpened containers must be tightly resealed immediately after use and consumed as soon as possible. S-990 contains isocyanates and is reactive.\u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":62357912027466,"sku":"1232","price":43.69,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/Arcan-Bauchemie-Sandteppich-Schwarz-e1445431623541.jpg?v=1788190580"},{"product_id":"duroflex-671-universeller-primer-fur-mineralische-untergrunde-und-asphalt-1-liter-kopie","title":"DuroFlex 671 - universal primer for mineral substrates and asphalt 5 liters","description":"\u003cp class=\"Normal tm5\"\u003e\u003cspan class=\"tm6\"\u003e1K primer and impregnating sealer for concrete and asphalt\u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"Normal tm5\"\u003e\u003cstrong\u003e\u003cspan class=\"tm6\"\u003eDuroFlex 671 is a ready-to-use polyurethane coating material. The product cures by reacting with traces of atmospheric moisture to form elastic, resistant layers with excellent adhesion to almost any substrate.\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp class=\"Normal tm5\"\u003e\u003cspan class=\"tm7\"\u003eDue to its excellent substrate adhesion, \u003c\/span\u003e\u003cspan class=\"tm8\"\u003eDuroFlex 671\u003c\/span\u003e\u003cspan class=\"tm7\"\u003e is perfectly suited as a bonding agent for subsequent coatings, preferably on difficult, bituminous substrates. Such surfaces can also be sealed and protected from wear, and to a limited extent even from the effects of oil and fuel, by treating them twice or more with \u003c\/span\u003e\u003cspan class=\"tm8\"\u003eDuroFlex 671\u003c\/span\u003e\u003cspan class=\"tm7\"\u003e. \u003c\/span\u003e\u003cspan class=\"tm7\"\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"Normal tm5\"\u003e\u003cspan class=\"tm7\"\u003eSealings with \u003c\/span\u003e\u003cspan class=\"tm8\"\u003eDuroFlex 671\u003c\/span\u003e\u003cspan class=\"tm7\"\u003e have a satin to glossy finish and dry clear. The films provide excellent surface protection and are abrasion-resistant.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"Normal tm5\"\u003e\u003cspan class=\"tm7\"\u003e\u003cstrong\u003eContent: \u003c\/strong\u003e5 liters\u003c\/span\u003e\u003c\/p\u003e","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":63279730721098,"sku":"1198-5","price":83.71,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/Bild1.jpg?v=1787841535"},{"product_id":"silox-dichtschlamme-863-universelle-abdichtungs-und-beschichtungsmasse-2kg","title":"Silox Sealing Slurry 863 – universal sealing and coating compound 2kg gray","description":"\u003cp\u003e\u003cstrong\u003eSpecial coloring for water basins\u003c\/strong\u003e - \u003cstrong\u003eSilox 863\u003c\/strong\u003e is a universal sealing and coating compound for all cement-bonded building materials. \u003cstrong\u003eSilox 863\u003c\/strong\u003e is absolutely watertight yet breathable, can be applied to damp substrates, and withstands high water pressure. \u003cstrong\u003eSilox 863\u003c\/strong\u003e is sag-resistant and highly adhesive, making it easy to use even on uneven walls with deep surface roughness or overhead. \u003cstrong\u003eSilox 863\u003c\/strong\u003e adheres excellently to damp, mineral substrates and metals. If the substrate is clean and sound, no special primers or base coats are necessary. Blowhole- and pore-free coatings are completely liquid-tight but remain breathable. Its excellent mechanical properties (hardness, abrasion resistance) also make it suitable for sealing floor surfaces, e.g., in basements and underground garages. \u003cstrong\u003eSilox 863\u003c\/strong\u003e can also be used for reprofiling damaged concrete surfaces (wet-on-wet), as a bonding agent between old and new concrete, as an adhesive for natural and artificial stone, as an anchor mortar, and for similar applications.\u003c\/p\u003e\n\u003ch4\u003eSubstrate Requirements\u003c\/h4\u003e\n\u003cp\u003eThe substrate must be clean and free of contaminants or coatings that act as separating agents. Mineral substrates must be sufficiently firm and sound; the tensile strength should not fall below 1.5 N\/mm2 over the entire area. Laitance layers on concrete and screed must be removed, and blowholes and pores must be opened. Iron and steel must be derusted to a bright metal finish (SA 2½); scale and mill scale must be removed. \u003cstrong\u003eSilox 863\u003c\/strong\u003e is not suitable for plastics or substrates bonded with bitumen, asphalt, or tar.\u003c\/p\u003e\n\u003ch4\u003eMixing\u003c\/h4\u003e\n\u003cp\u003eEmpty component A completely into the container of component B and stir with a mixing machine until the color of the mixture is uniform and free of streaks. Then, transfer the mixture as usual and mix thoroughly once more. Do not stir in any air! The mixture stiffens significantly during the mixing process and becomes tacky and plastic. This effect is typical for the product and supports the exceptionally good sag resistance of \u003cstrong\u003eSilox 863\u003c\/strong\u003e on vertical surfaces and smooth substrates. Adding a little water - \u003cstrong\u003ea maximum of 5% - makes the mixture more fluid while remaining sufficiently sag-resistant\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch4\u003eApplication\u003c\/h4\u003e\n\u003cp\u003eSilox 863 is applied manually with standard tools (spatula, trowel, pointing trowel, notched trowel) and can also be sprayed like thin-layer plasters or sealing slurries using light spray machines (screw pumps). Depending on the spray pressure and the supporting air volume, this produces more or less finely textured, uniform surfaces.\u003c\/p\u003e\n\u003ch4\u003eCleaning\u003c\/h4\u003e\n\u003cp\u003eMachines and tools should be cleaned with water, ideally mixed with a little dish soap. Fresh contamination from the material should also be removed by washing with water.\u003c\/p\u003e\n\u003ch4\u003ePot Life\u003c\/h4\u003e\n\u003cp\u003eThe pot life of a mixture not additionally diluted with water is approx. 30 - 40 minutes at 20°C. In strong air currents or direct sunlight, a type of skin formation may occur earlier on the surface of freshly applied layers. Such surfaces should not be reworked by smoothing afterwards.\u003c\/p\u003e\n\u003ch4\u003eSubsequent Coatings\u003c\/h4\u003e\n\u003cp\u003eCoatings made of Silox 863 can be recoated with themselves or with breathable EP sealers (SILOX-857) after a waiting period of 24 hours. For diffusion-tight topcoats, a waiting period of 96 hours (at 20°C) is recommended.\u003c\/p\u003e\n\u003ch4\u003eBoundary Conditions\u003c\/h4\u003e\n\u003cp\u003eThe minimum temperature of the substrates should not fall below +9°C. The product must not be applied to glossy wet substrates. To prevent \"burning\" on highly absorbent substrates, moisten such surfaces before application or, even better, prime with Silox-856. Color: dark gray. Tested up to 7 bar negative water pressure!\u003c\/p\u003e\n\u003ch4\u003eContainer\/Variants:\u003c\/h4\u003e\n\u003cul\u003e\n\n\u003cli\u003e2.0 kg gray - contains components A and B in total\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"ARCAN","offers":[{"title":"Default Title","offer_id":63280023241034,"sku":"1209-2kg","price":39.35,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/files\/010.jpg?v=1787841565"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1047\/8626\/4394\/collections\/Kategorie-Beschichtung.png?v=1785174887","url":"https:\/\/shop.arcan.biz\/en\/collections\/beschichtungen.oembed","provider":"ARCAN GmbH Abdichtungen – Handwerkerstore","version":"1.0","type":"link"}